Getting ready for your floor Everything people ask us

When can I park on it? EVERYTHING ELSE TOO.

For houses, apartments, shops, offices and plants alike. How long before you can walk on it, move things back and park the car. What has to come off the floor, what doesn't, and how much dust to expect. The straight answers, all in one place.

Your timeline

Pick your floor and the day we start.

Temperature in the space

    Cold slows everything down. We'll give you your exact times on the day.

    Times are from the manufacturer's data sheets Rated at 72°F Cold space: air and slab within 10°F
    Before we come

    Clear the floor. That's the big one.

    What has to come off the floor?

    Everything. Boxes, bins, bikes, tools, shoes, the recycling. If it's on the floor, it has to be gone before we get there. We can't grind or coat around your things.

    Need help with something heavy, like a fridge, a gun safe or a workbench? Tell us when you book. We'll help with the big items. All the smaller stuff needs to be moved by you.

    Do I have to take things off the walls?

    No. Shelves, cabinets, pegboard and things hanging on the walls can stay. We only need the floor.

    Should I clean the floor first?

    No. We grind the whole surface anyway. If you want to sweep it, that's fine. Please just pick up any metal pieces, screws or chunks lying around.

    What about electronics?

    We cover them with plastic. A few items are no extra charge. If a whole room or a lot of equipment needs to be sealed off, we plan that into the price up front. We've plastic-wrapped entire rooms in working buildings before.

    Do the cars need to be out?

    Yes, out of the garage and parked somewhere else until you're cleared to park. Plan on it for the whole job plus the cure time on your timeline.

    While we're there

    Is it going to be dusty?

    Much less than you'd think. Every grinder runs connected to dust collection. The dust first goes through a separator that drops out the heavy dust, so the vacuum behind it only has to catch what's left. That vacuum has a HEPA filter, the kind rated to catch 99.97% of the finest particles.

    There will still be a little. Think of it like the dust you'd find if nobody had dusted the place in a couple of weeks.

    GrinderShroud around the diamonds, hooked to the hose
    SeparatorDrops out most of the heavy dust first
    HEPA vacuumCatches the fine dust that's left: 99.97% at the finest particle size
    What's leftA light layer, like two weeks without dusting

    Can we walk across it while you work?

    No. Once the base coat goes down, nobody walks on it until it's ready. Plan another way in and out of the building for those days.

    Kids and pets?

    Keep them out of the work area until you can walk on the floor. A paw print in a wet coating is there for good.

    Will it smell?

    Not really. Here's why.

    Our epoxies and urethane cement are 100% solids. Our topcoats are high solids, over 90%. That number matters more than almost anything else on a data sheet.

    Solids is the part of a coating that stays on your floor. The rest is thinners, reducers and solvents. They're there to cheapen it or make it easier to roll, and they evaporate. That's the smell. It's also coating you paid for that just left your floor.

    Put down 10 mils of a 100% solids epoxy and you keep 10 mils. Put down 10 mils of a 70% solids product and you're left with 7. The other 3 went into the air you breathe.

    Solids content100%
    Rolled on
    10 mils
    Left on your floor
    10 mils

    Nothing evaporates. What we put down is what you keep, and there's almost nothing in the air.

    After we leave

    Give it the full cure.

    Walking on it and parking on it come first. A coating keeps hardening for days after that, so go easy for the first week.

    When can I put rugs or mats down?

    Wait until it's fully cured, about 5 to 7 days depending on the floor. Rubber mats on a fresh coating can mark it.

    When can I wash it?

    Dry sweeping is fine right away. Hold off on mopping with cleaners, power washing and any solvents until it's fully cured, about a week. Then see how to clean it.

    What about hot tires?

    You can park after 24 hours. For the first week, skip pulling in right after a long drive on a hot day, like straight off the highway from Pittsburgh in July. The topcoat is still finishing its cure, and very hot tires can react with it and leave a mark. Around town is fine. After the first week, it's built to handle them.

    Caring for your floor

    How to clean it. What not to use.

    A coated floor is about the easiest floor there is to keep clean. Here's everything we tell people, in one place.

    Every week or so

    Sweep, then soap and water

    Dust mop or sweep to get the grit off. Grit is what scratches a floor. Then mop with warm water and a little mild soap, or Simple Green mixed per the label. A microfiber mop or a soft brush is all you need.

    Rinse with clean water when you're done. Leftover soap film can make the floor slick when it's wet.

    A few times a year

    Power wash it

    We recommend it. It's the fastest way to get a garage or shop floor back to new.

    0°15°25°40°

    Use the 25° (green) or 40° (white) tip, never the 0° or 15°. Keep the tip at least a foot off the floor and keep it moving. Go easy at the edges, where the floor meets the walls.

    Tough spots

    Stains, tire marks, rust

    1. Simple Green. Let it sit a few minutes, then scrub with a stiff nylon brush.
    2. Goof Off or brake cleaner. A little on a rag, wipe the spot, rinse. Don't pour it on or let it puddle.
    3. Rust: CLR, on the spot only. A minute or two, never let it dry, then rinse with plenty of water. We use it on rust spots ourselves. It's a mild acid, so keep it to the spot and get it right back up.
    4. Still there? Call us.

    Wait until the floor is a week old before using any of these. Open the door when you use solvents.

    Don't use
    • Vinegar or citrus cleaners. They're acids and slowly dull the shine.
    • Bleach or harsh acids like muriatic acid.
    • Steel wool, wire brushes or scouring powder.
    • Magic Erasers on a gloss floor. They work like very fine sandpaper and leave a dull patch.
    • The 0° or 15° pressure washer tip.

    Spills

    Wipe up oil, antifreeze, brake fluid and road salt water when you see them. The floor resists them, but nothing should sit for weeks. Salt and slush in winter: squeegee it out the door and rinse it now and then.

    Polished concrete and grind and seal

    Dust mop, then a neutral floor cleaner (pH-neutral on the label) and water. No vinegar, no acids. Big commercial floors: an auto scrubber with soft pads.

    Questions we didn't answer?

    Call us. We'll walk you through it.

    Every job is a little different. When we schedule yours, we'll give you the exact days and times for your floor, your space and the weather that week.

    Phone(814) 812-3118
    Emailoffice@814epoxyandmore.com
    Address1310 Lowell Ave, Erie, PA 16505

    We only use this to get back to you about your floor. Privacy