FAQ The questions people really ask us

Straight answers. NO SALES PITCH.

These are the questions we hear on the phone and in our inbox, answered the way we'd answer them standing on your slab.

41 questions

Price and quotes

How much does an epoxy floor cost?

It depends on the floor you pick, the condition of your slab, the size of the space and what the concrete needs before anything goes down. Two garages the same size can need very different prep, and the prep drives the price as much as the coating does.

So we don't give a price per square foot over the phone without seeing the slab. We come out, look at the concrete, tell you what it needs and give you a firm number. The estimate is free.

What do you need from me to give a quote? Can I just send pictures?

Pictures are a great start. Send a few close-up photos of the floor, plus one wide shot of the room, and tell us roughly how big it is and what it's used for. Close-ups of the concrete usually tell us a lot about the prep it needs.

For bigger jobs, or a floor with something unusual going on, we'll come walk it with you instead of trading photos. Either way the estimate is free.

Can I see a sample first?

Yes. We bring real samples to your floor so you see the color in your own light, not on a screen. If you want a custom flake mix, we can make up a sample of that too.

Why is your quote different from another contractor's?

Usually because the job is different. If someone quoted less, ask them:

  • Are you diamond grinding the concrete, or just acid etching it?
  • What's the solids content of your coatings?
  • Is there a moisture-blocking base coat?
  • How thick is the finished floor?

A cheaper quote usually means less prep, thinner coats or lower-solids products. None of that shows on day one. It shows a couple of winters later. Our garage buyer's guide has a checklist you can take to any contractor, us included.

Do you offer financing?

No, we don't offer financing.

Picking a floor

Which floor is right for my space?

That's what the site visit is for. We look at your concrete, what the space is used for, what rolls across it and what spills on it, then recommend what we'd put in our own building. We spec what the space needs and show you why; we don't push the most expensive system on a slab that doesn't need it.

For garages it's usually flake. Kitchens and food plants get urethane cement. Shops with forklifts and jacks get STS Shop Tough. New concrete in good shape that just needs protecting gets Lite Tough Urethane.

Every floor we do is side by side on our floor systems overview: tell it where the floor is going and it shows the ones that fit.

What's the difference between epoxy and polyaspartic?

They do different jobs, so we use both. Epoxy soaks into the concrete, bonds hard and blocks moisture coming up from below, so it's our base coat. Polyaspartic is tough, holds up to chemicals and scratches, and won't yellow in sunlight, so it's our topcoat.

What we don't do is polyaspartic or polyurea from top to bottom in one day. That skips the base coat that keeps a floor down through Erie winters. Polyurea vs epoxy explains why.

Do you do one-day garage floors?

No. A one-day floor only grabs the surface of the slab, and in our climate moisture from below and salt from above work at that bond every winter. We take the extra day for a moisture-blocking epoxy base that soaks into the concrete. If one day worked here, we'd do it too; it would be more garages a week for us. Here's the long answer.

What is solids content, and why does it matter?

It's how much of the coating stays on your floor after it cures. The rest evaporates, and that's the smell.

Roll on 10 mils of a 100% solids coating and you keep 10 mils of floor. Roll on 10 mils of a 70% solids coating and you keep 7. Our epoxy base coats are 100% solids, and our topcoats are over 90%. Any contractor should be able to show you the data sheet.

What flake colors do you have?

Ten Signature Blends: Domino, Wombat, Nightfall, Gravel, Orbit, Tidal Wave, Creekbed, Cabin Fever, Shoreline and Outback. You can throw them on a floor yourself on our flake floors page, or try one on a photo of your own room in the floor visualizer. We bring real samples to your floor before you choose.

Can you make it non-slip?

Yes. Grit goes into the topcoat: polypropylene on most floors, aluminum oxide where the floor also has to fight scratches, and sand for the most texture where it gets wet or greasy. Epoxy quartz is the grippiest floor we do. More grip means a little more work to mop, so we match it to the space.

Can polished concrete be colored?

Yes. Dye soaks into the slab before the final polish, so the color is part of the floor and there's nothing on top to peel. Dye mottles a little differently on every slab, so we test a spot first, and sunny rooms get UV-stable dyes. See dyed polished concrete.

Do you do kennels and dog runs?

Yes. A kennel needs a seamless floor that takes hosing and cleaners every day and gives paws some grip. We usually spec urethane cement or epoxy quartz, with integrated cove up the walls so nothing gets into the corners. We'll recommend one once we've seen the space.

Can I get a metallic floor in my garage?

We don't put metallic floors in garages. Our winters, salt and hot tires are too hard on a high-gloss decorative floor. For a garage we point you to flake. Metallic is for indoor rooms: basements, showrooms, bars, salons and offices. See metallic epoxy.

Do you do countertops?

We've done them, but we don't offer them. For most customers they just aren't cost effective.

Your slab

My concrete has cracks. Can you still coat it?

Yes, and we repair them first. Cracks and broken spots get filled with our polyurea and sand paste, which hardens in minutes, then ground flush before anything goes over it. A crack coated over without a repair shows right back through. Crack and joint filling shows how we do it.

My concrete is brand new, or about to be poured. When can you coat it?

New concrete needs to cure about a month before it gets coated. We still grind it: every floor gets ground, new concrete included, because a fresh slab has a smooth, weak skin on top that a coating can't hold onto. If your pour is coming up, call us now and we'll plan the date around it.

Can you go right over my tile, LVT, old sealer or old coating?

Usually it comes off. A new floor is only as good as what it's bonded to, and putting it over tile, vinyl, glue, sealer or a peeling coating is one of the most common ways floors fail. We remove it and grind down to clean concrete; that work is in your quote.

If an old coating is tight and sound everywhere, we'll tell you the options when we see it.

The coating on my outdoor steps or porch is peeling. Can you redo it?

Yes. Peeling outdoor coatings are usually paint or a thin coating that was rolled on without real prep. We grind it off, repair the concrete, and put down a floor made for outdoors, like epoxy quartz with a clear polyaspartic top that won't yellow in the sun, or the Slurry System. Steps and porches are some of our favorite before-and-afters.

My slab is old and rough. Can it still look good?

Usually, yes. A rough or pitted slab under a flake floor is a good candidate, because the repairs and the flake hide a lot. A rough slab that you want polished needs a closer look, and sometimes an overlay first. We'll tell you what's realistic.

My floor has radiant heat in it. Can you still coat or polish it?

Usually, yes. We need to know where the tubing runs and how deep it is, so we never grind or cut near it. The heat gets turned down while the floor goes in and cures, then brought back up slowly. Tell us about it when you call.

Can you match a floor that's already there?

We can get close, often very close, but a new floor next to an old one rarely matches exactly: the old one has years of sun and wear on it. When it matters, we'll suggest a clean break at a doorway or a joint so the two never sit side by side.

What about moisture coming up through my concrete?

We test the slab for moisture before we pick the system. Our coated floors start with a moisture-blocking epoxy base that soaks into the concrete, built for Erie slabs. If a slab has more moisture than a floor can handle, we'll tell you before we quote it, not after it fails.

When we put down a moisture vapor barrier, your floor is covered against peeling and delamination from moisture coming up through the slab. Without one, moisture from the slab isn't covered. Your contract says which you're getting.

The install

How long does the install take?

A flake floor in a garage or basement usually takes three to four days. A typical basement goes: day one, grind and repair; day two, the moisture-blocking base and flake; day three, scrape and a clear grout coat; day four, the topcoat. You can start moving things back the day after we finish. Small, simple rooms can go quicker.

Commercial jobs depend on the size and the system, and we can work in sections around your schedule.

Metallic floors depend on the design, so we give you a timeline after we've seen the space and talked it through.

When can I walk on it and park on it?

On a flake garage floor, you can usually walk on it the next day and park on it after about 24 hours. It's fully cured in about a week; for that first week, don't pull in right after a long, hot highway drive. Cold weather stretches every time.

Getting ready for your floor has a timeline for every system: pick your floor and your start day and it shows when you can walk, move things back and park.

What do I need to do before you come?

Clear the floor: everything off it, and the cars out the night before. Things on the walls can stay. You don't need to clean it; we grind, clean and mask everything ourselves. The full list is on getting ready for your floor.

Is it dusty? Does it smell?

Not much on either. Our grinders run through a separator into a HEPA vacuum, so the dust goes into a bag, not into your building. And because our base coats are 100% solids and our topcoats are over 90%, there's very little to evaporate, which is what makes the smell.

Do you work in the winter?

Yes. Indoors with heat, winter is rarely a problem. A cold slab cures slower, so we plan around it. What matters most is keeping the air and the slab within about 10 degrees of each other, so we heat the space ahead of time and check both. If the slab or the air isn't right we'll tell you and reschedule instead of forcing it.

When can you fit me in?

It depends on the season. Spring through early fall fills up fastest, mostly with garages; winter usually has more openings, and indoor jobs go fine in winter. If you have a date you need to hit, tell us up front and we'll tell you straight whether we can make it. For a spring job, call as early as you can.

After the install

How do I clean my floor?

Sweep or dust mop often, then mop with soap and water or Simple Green. You can power wash it with a 25 or 40 degree tip, a foot or more off the floor; never a 0 or 15. Don't use vinegar or citrus cleaners, bleach, harsh acids or steel wool.

Stains, tire marks and rust are covered step by step in the full cleaning guide.

Are hot tires, salt and oil OK on a flake floor?

Yes, once it's cured. That's what a flake garage floor is built for. Wipe up oil and gas when you see them, and rinse the salt off more often in winter. The one thing to avoid is pulling in after a long, hot drive during the first week while the topcoat is still curing.

My floor got scratched or dull. Can it be fixed?

Call us and we'll take a look. The topcoat is the layer built to take the wear, so scratches and a dull walking lane are normal over the years. When it's time, a topcoat refresh brings the floor back: we scrub it, sand it lightly and put down a fresh topcoat.

How long will my floor last?

Done right and taken care of, a long time. Our coated floors carry a 15-year warranty, and the floor underneath keeps going well past that with a topcoat refresh every several years. A grind and seal floor needs a fresh coat of sealer every few years, depending on traffic. Urethane cement is the toughest floor we install.

The biggest factor isn't the product. It's the prep under it.

Warranty

What's your warranty?

Every warranty we give covers workmanship and materials. Our coated floors (flake, metallic, quartz, Slurry System, STS, Lite Tough Urethane and urethane cement) are covered for 15 years indoors. Anything outdoors (steps, porches, patios, pool decks) is 5 years, because sun, freeze-thaw and salt are things no prep can control. Polished concrete and crack repairs carry 7 years; grind and seal, Tread-Plex and outdoor pool deck coatings carry 3. If one fails because of our work or our materials, we come back and fix it at no cost.

The manufacturers back their products for about a year. We give 15 because the prep is ours and these products have proven themselves when the prep is right. Every floor's warranty is on warranty and maintenance.

If I sell my building, does the warranty go with it?

Yes. The warranty goes to the next owner for the years that are left. Keep your contract with the property papers; it's the proof.

Do you offer a lifetime warranty?

No. Nobody can honestly promise a floor forever, and we'd rather promise what we can stand behind: 15 years on our coated floors indoors, 5 outdoors, in writing.

Is the topcoat covered?

No. The topcoat is the sacrificial layer: it takes the wear so the floor under it doesn't, and it gets renewed. Hot tire pickup is a topcoat issue too. The warranty covers the floor itself.

About us

Where do you work?

We're based in Erie and work across Northwest Pennsylvania: Erie, Crawford, Warren and Venango counties and the counties around them. We'll travel farther when the job makes sense for both of us; we've worked in Pittsburgh, Buffalo and Cleveland. If you're outside our area, call us.

Are you licensed and insured?

Yes. PA Contractor #165436, fully insured. We provide proof of insurance for commercial and institutional jobs that need it; just ask.

Do you use subcontractors?

No. Every job is done by our own crew, so you get the same people every time and the people who built your floor are the ones who stand behind it.

Do you do homes and businesses?

Both. Healthcare, nonprofits, schools, commercial buildings, shops and plants, and homes: garages, basements and living spaces. The floors differ; the standard doesn't. Every floor we put down is built to an industrial standard.

Still have a question?

Ask the people who do the work.

We're a local business with real people who answer. If you ask it and someone else does too, it ends up on this page.

Phone(814) 812-3118
Emailoffice@814epoxyandmore.com
AreaErie, PA and surrounding counties

We only use this to get back to you about your floor. Privacy